TS-200 200mmBasic Table SawAxminster Tool Centre,Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PHaxminster.co.ukCode: 501242Product Code Kits717218:
10ALWAYS disconnect the machine if you are leaving it unattended.NEVER leave the vicinity of the machine unless the blade has come to a complete stop.
11Assembly InstructionsInitial AssemblyPlease take some time to read the section entitled “Identification and Parts Description” toidentify the variou
12Assembly InstructionsWith assistance, place the Saw Bench (A) onto the stand. Align the four mountingholes at the base of the Saw Bench with the fou
Locate the sliding carriage table (D) and slide it onto the carriage arm (V), see fig 10. Usinga level or straight edge place across the sliding table
14Assembly InstructionsAngle Fence AssemblyPut to hand the work clamp block (O), and slide it onto the T-slot on the angle fence (W).Locate the connec
15Assembly InstructionsAngle Fence Assembly To set the angle fence (W) to angles between 45˚ and 90˚ loosen the three lift and shifthandles on the con
16Assembly InstructionsFig 26Fig 27Fig 28Fig 29Fig 30Fig 31Locate the two operating wheel handles (F) and, using the supplied 3mm allen key (J),secure
17Assembly InstructionsLocate the two extension table support arms (X). Remove the plastic cover to the left handside of the support arm with the scal
18Assembly InstructionsExtension Table Assembly Part 2Fence AssemblyRemove the plastic covers from the ends of the two extension table support arms (X
19Assembly InstructionsFence Assembly Lower the fence assemby so the clamp assembly (N) slots over the extention table supportarm (X), clamp the fence
Declaration of ConformityPage No.Index of Contents02Index of Contents 02Declaration of Conformity 02Parts Index 03-04-05-06-07General Instructions for
20Assembly InstructionsDust Extraction Assembly Fig 50Fig 51Fig 52Fig 53(717218 Only) Remove the nuts, bolts & washers from the 30mm hose support
21Illustration & Parts DescriptionAFQSXYZFVUTRPMWONCDEGA Saw Bench M Flip Over StopB1 Push Stick O Work Clamp/Connecting BlocksC Work Clamp Assemb
22Illustration & Parts DescriptionAVHLIDYZXB1Z1Z1X Extension Table Support Arms Z FenceY Extension Table Z1 Hoses 50mm & 30mm
23Setup & AdjustmentsFig 54Fig 55Fig 56Fig 57Fig 58Fig 59Adjusting the Riving KnifeAdjusting the Fence to the BladeRaise the saw blade to its high
24Setup & AdjustmentsAdjusting the Fence to the BladeFig 62Fig 63The fence (Z) can be repositioned to face the opposite direction for guiding thin
NOTE: Secure larger pieces of timber to the table by using the clamp assembly (C), seepage 20.25Operating InstructionsNOTE: Before using your table sa
26Operating InstructionsThe Mitre FenceThe mitre fence can be mounted on either side of the saw blade in the two ‘T’ slots, premachined into the saw t
27Changing the Saw BladeFig 69Fig 70Tighten up the saw bolt, check the riving knife is aligned with the saw blade, and correctlypositioned. Replace th
28Parts Breakdown for TS-200 Table Saw
29Parts Breakdown for TS-200 Table Saw
03Parts IndexModel Number: HM-TS2001 off Basic Table Saw (with Saw Blade & Riving Knife fitted) A2 off Sliding Carriage Supporting Arms B1 off Pu
30Parts List for TS-200 Table Saw
31Parts LIst & Breakdown for the Sliding Carriage
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging
04Parts Index32 off M8 x 12 Coach Bolts with Nuts4 off M8 x 11 Bolts with Large Washer & Nut T1 off Saw Guard with M6 x 25 Coach Bolt & Nut U1
05Parts IndexCDEIJFGHKMNOLBox
06Parts IndexPQRSTUVWW1W1X
Parts IndexYZZ1Z1Z2Z307General Instructions for 230V MachinesThe following suggestions will enable you to observe good workingpractices, keep yourself
08General Instructions for 230V MachinesWork Place/Environment The machine is not designed for sub-aqua operation, do not use when or where it is liab
09General Instructions for 230V MachinesDO NOT use this machine within the designated safety areas of flammable liquid stores orin areas where there m
Commentaires sur ces manuels